| DTP HDMI 4K 230 D Tx/Rx |
|
 specification |
|---|
 |
| Frame rate1 | 24, 25, 30, 50, or 60 fps |
| Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:0 |
| Color bit depth1 | 8 bits per color |
| Signal Type | HDMI 1.4, HDCP 2.3 |
| Max. video data rate | 10.2 Gbps (3.4 Gbps per color) |
| NOTE | 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate. |
|
|
| Video |
|---|
| Maximum data rate | 10.2 Gbps (3.4 Gbps per color) |
| Maximum pixel clock | 300 MHz |
| Resolution range | Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz,
4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(*Reduced blanking) |
| Color bit depth | 8, 10, or 12 bits — subject to the maximum data rate limit |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E |
|
| Video input — transmitter |
|---|
| Number/signal type | 1 single link HDMI (or DVI-D*) input |
| Connectors | 1 female HDMI type A |
| NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for HDMI signal input/output. |
|
|
| Interconnection between transmitter and receiver |
|---|
| Connectors | 1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver |
| Termination standards | TIA/EIA T568B |
| DTP signal | |
| Signal transmission distance | |
| 1080p @ 60 Hz | Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable |
| 2560x1600 @ 60 Hz | Up to 130' (40 m) using STP cable or XTP DTP 24 cable |
| 4K/UHD @ 30 and 60 Hz | Up to 130' (40 m) using STP cable or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth STP cable |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Video output — receiver |
|---|
| Number/signal type | 1 single link HDMI (or DVI-D*) |
| Connectors | 1 female HDMI type A |
|
| Audio |
|---|
| Gain | Unbalanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | 0.03% @ 1 kHz at nominal level, 0.3% @ 20 kHz at nominal level |
| S/N | >90 dB, at maximum output (unweighted) |
| Stereo channel separation | >80 dB @ 1 kHz to 20 kHz |
|
| Audio input — transmitter |
|---|
| Number/signal type | 1 PC level stereo, unbalanced |
| NOTE | Analog audio is not embedded onto the digital video signal. Embedded digital audio is not de-embedded from the digital video signal. |
|
| Connectors | (1) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (ground) |
| Impedance | 20k ohms, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +6 dBu, unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — receiver |
|---|
| Number/signal type | 1 stereo (2 channel), unbalanced |
| Connectors | (1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground) |
| Impedance | 50 ohms, unbalanced |
| Gain error | ±0.2 dB channel to channel |
| Maximum level (600 ohm) | >+7 dBu, unbalanced at 1% THD+N |
|
| Control/remote — external device (pass-through, unidirectional or bidirectional) |
|---|
| Serial control port input | |
| Transmitter | RS-232 via (1) 3.5 mm, 5 pole captive screw connector
(connector is shared with IR control port) |
| Receiver | 1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output | |
| Transmitter | 1 set of proprietary signals on a female RJ-45 jack |
| Receiver | RS-232 via a 3.5 mm, 5 pole captive screw connector |
| NOTE | Protocol is mirrored between the transmitter and the receiver. |
|
| Baud rate and protocol | 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity |
| Serial control pin configuration | Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd |
| IR control port | (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
| IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Transmitter | |
| Device | 2.8 watts, 12 VDC |
| Device and power supply | 3.8 watts, 100-240 VAC, 50-60 Hz |
| Remote power budget | 18 watts |
| Receiver | |
| Device | 4.2 watts, 12 VDC |
| Device and power supply | 5.9 watts, 100-240 VAC, 50-60 Hz |
| Remote power budget | 18 watts |
| NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Transmitter | |
| Device | 8.3 BTU/hr |
| Device and power supply | 11.8 BTU/hr |
| Receiver | |
| Device | 13.1 BTU/hr |
| Device and power supply | 18.8 BTU/hr |
| Mounting | |
| Furniture or wall mount | Yes, with a 2-gang wall box or mud ring |
| Enclosure type | Metal |
| Enclosure dimensions | |
| Faceplate | 2.6" H x 1.3" W x 0.1" D
(6.6 cm H x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 2 gang decorator wallplate.) |
| Device | 2.7" H x 3.5" W x 1.8" D
(6.9 cm H x 8.7 cm W x 4.5 cm D) |
| NOTE | Height excludes mounting tabs, depth excludes connectors. |
|
| Product weight | 0.4 lbs (0.2 kg) |
| Regulatory compliance | c-UL, C-tick, CE**, FCC Class A**, ICES, KC, UL, VCCI |
| NOTE | **CE and FCC testing is conducted with STP cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5371-D14) |