| FOXBOX 4G DVI Series |
| NOTE | These transceivers are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11. |
|
|
| Optical fiber interconnection between transmitter and receiver |
|---|
| Number/type | 1 or 2 fiber optic |
| Connectors | 2 LC connectors |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with a FOXBOX 4G SM |
| Multimode | 300 m (985') with 62.5 µm multimode (MM) cables with a FOXBOX 4G MM
1 km (3280') with 50 µm multimode (MM) cables with a FOXBOX 4G MM
2 km (6561') with 50 µm 2000 MHz bandwidth laser optimized multimode cable with a FOXBOX 4G |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for FOXBOX 4G MM, 1310 nm for FOXBOX 4G SM |
| Data rate | 4.25 Gbps |
| Transmission power | |
| Singlemode | -5 dBm, typical |
| Multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
|
| Video |
|---|
| NOTE | *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. The FOXBOX 4G Tx/Rx DVI Series can be used to distribute HDMI signals if you use a DVI-to-HDMI adapter. However, when using HDMI signals, these units do not transmit audio and CEC signals.
The FOXBOX 4G Tx/Rx DVI does not support transmission of DVI signals with High-bandwidth Digital Content Protection (HDCP). |
|
| Resolution range | Up to 1600x1200 or 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI 1.2 |
|
| Video input — transmitter |
|---|
| Number/signal type | 1 single link DVI-D (or HDMI*) |
| Connectors | 1 female DVI-I |
|
| Video output — receiver |
|---|
| Number/signal type | 1 single link DVI-D (or HDMI*) |
| Connectors | 1 female DVI-I |
| Nominal level | 0.8 Vp-p |
| Video delay | 1-2 frames |
|
| Audio |
|---|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | Unbalanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| CMRR | 65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio input — transmitter |
|---|
| Number/signal type | 1 unbalanced stereo or 2 unbalanced mono |
| Connectors | (1) 3.5 mm mini stereo jack |
| Impedance | 18k ohms unbalanced, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +8.9 dBV, (unbalanced) at 1% THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — receiver |
|---|
| Number/signal type | 1 unbalanced stereo or 2 unbalanced mono |
| Connectors | (1) 3.5 mm mini stereo jack |
| Impedance | 50 ohms unbalanced |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level (Hi-Z) | +7.6 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+6.3 dBu, unbalanced at 1% THD+N |
| Audio delay | 1.5 frames |
|
| Control/remote |
|---|
| Serial control ports on each unit (transmitter and receiver) |
| Control | 1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel) |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115,200 baud |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set™ (SIS™) |
|
| General |
|---|
| External power supply | 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
| Power input requirements | 12 VDC, 0.6 A |
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and side panels |
| Thermal dissipation | |
| Transmitter | |
| 115 VAC, 60 Hz | 7.7 BTU/hr |
| 240 VAC, 50 Hz | 11.0 BTU/hr |
| Receiver | |
| 115 VAC, 60 Hz | 7.2 BTU/hr |
| 240 VAC, 50 Hz | 10.5 BTU/hr |
| Mounting | |
| Rack mount | Yes, with optional rack shelf |
| Furniture mount | Yes, with optional under desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight | 0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair |
| Shipping weight | 3 lbs (2 kg) per unit, 6 lbs (3 kg) per pair |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, FDA Class 1, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| MTBF | 30,000 hours |
| Warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.6-030410-D11) |