| FOXBOX Rx VGA |
| NOTE | The FOXBOX Rx VGA is a receiver with one or two fiber optic cables linking it to a transmitter. It is available in singlemode or multimode versions. |
|
| NOTE | The analog RGB input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog RGB in the receiver. |
|
| NOTE | The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. |
|
| NOTE | This receiver is a class 1 laser product. It meets the safety regulations of IEC-60825. |
|
|
| Optical fiber interconnection between transmitter and receiver |
|---|
| Number/type | 1 or 2 fiber optic |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control and communication. |
|
| Connectors | 2 LC connectors |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with SM units |
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cables with MM units
1 km (3280') with 50 µm OM2 multimode (MM) cables with MM units
2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized multimode cable with MM units |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for MM, 1310 nm for SM |
| Data rate | 4.25 Gbps |
| Transmission power | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
|
| Video |
|---|
| Signal Type | VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Gain | Unity |
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B; or YUV) |
| Resolution range | 640x480 to 1600x1200 @ 60Hz or 480p, 576p, 720p, 1080i, 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled |
|
| Video output |
|---|
| Number/signal type | With input from a FOXBOX Tx VGA:
1 VGA-UXGA RGBHV, RGsB (follows input or can be set by user)
With input from a FOXBOX Tx VGA/YUV:
1 VGA-UXGA RGBHV, RGBS, component video (bi- or tri-level YUV, 480p, 576p, 720p, 1080i, 1080p) |
| Connectors | 1 female 15 pin HD |
| Nominal level | 1 Vp-p for Y or component video
0.7 Vp-p for RGB and R-Y and B-Y of component video |
| Minimum/maximum levels | 0.3 V to 0.75 Vp-p, terminated |
| Impedance | 75 ohms |
| Return loss | -30 dB @ 5 MHz |
| DC offset | ±5 mV with input at 0 offset |
| Video delay | 1-2 frames |
|
| Sync |
|---|
| Output type | RGBHV, RGsB (follows input or can be set by user) |
| Output level | TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS
0.3 Vp-p for component video (bi-level sync, unterminated) or for Gs (SOG), terminated
0.6 Vp-p for component video (tri-level sync) |
| Output impedance | 75 ohms |
| Polarity | Positive or negative (follows input or can be set by user) |
|
| Audio |
|---|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | Unbalanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| CMRR | 65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio output |
|---|
| Number/signal type | 1 unbalanced stereo or 2 unbalanced mono |
| Connectors | (1) 3.5 mm mini stereo jack |
| Impedance | 50 ohms unbalanced |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level (Hi-Z) | +7.6 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+6.3 dBu, unbalanced at 1% THD+N |
| Audio delay | 1.5 frames |
|
| Control/remote |
|---|
| Serial control ports on each unit (transmitter and receiver) |
| Control | 1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel) |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115,200 baud |
| Serial control pin configuration | Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power input requirements | 12 VDC, 0.6 A |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and side panels |
| Thermal dissipation | 10.9 BTU/hr |
| Mounting | |
| Rack mount | Yes, with optional rack shelf |
| Furniture mount | Yes, with optional under desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.0" H x 4.3" W x 6.0" D (quarter rack wide)
(2.5 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight | 0.7 lbs (0.3 kg) per unit, 1.4 lbs (0.6 kg) per pair |
| Shipping weight | 3 lbs (2 kg) per unit, 6 lbs (3 kg) per pair |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.1-120914-D2) |